Hello Guys,Good Day !!This is very strange that : on version 20.9.4 the login banner is coming after the login prompt but it is perfectly coming on version 19.2.31 i.e. before login prompt.Would you please help me to fix : i am on version 20.9.4Early...
Forum Posts
Hello Guys,Good Day !!Need your help and guidance on cli commands to configure the NAT for the Internet Link on cisco cEdge for the direct L3 TLOC extension (Private IP address) between the 2 cEdges.In vEdge we can simply config NAT enable under the ...
Resolved! How can i match vsmart with each Tenant
Hello team Last day i upgraded all controller in to 20.3.5 -> 20.6.5 version as you know in 20.3.5 which use multitenant mode , the vsmart are bind in each tenant. but when i upgarde it 20.6.5 version. the vsmart are come out side. I want to use th...
Hi guys,My company has branches in 3 locations (the US, China, and Canada). I want to create a FULL-TUNNEL VPN for users who connect from coffee shops, airports, and hotels.I will do it using the Cisco profile editor and call it a UNSECURED VPN profi...
Resolved! cEdge lost connectvity to vManage
In my environment we have multiple cEdge devices, 1 vManage, 2 vBond and 2 vSmart.Due to some reasons one of the cEdge devices lost connectivity to vMange. Not sure of the exact reason.But would like to understand, will there be any impact due to thi...
Wanted to understand the best practices when updating the prefix-list & data prefix list in SD-WAN network.For example I have the below prefix-listlist_abc: 10.10.10.0/24This prefix list has been used in Centralized policy.I wanted to added new subne...
Hello Team,Please help me to understand: in hybrid scenario of Controller deployment, if vBond resides behind the NAT, and lets say cEdge on-boarding is done with the Internet as TLOC then as we know, vBond should learn both the Private and NATed pub...
Is it possible to mark a variable as optional in sd-wan cli template?Can we use variables in a local data policy? I want to apply an ACL to internet facing interface that only permits traffic to the internet facing IP only. Policy will be applied to ...
Can't update vManage from 20.9.1 to 20.9.2.1[1-Mar-2023 6:03:11 MSK] Device: Failed to install: Signature verification Suceeded.\nSignature verification Suceeded.\nSignature verification Suceeded.\nerror-reason 'ERROR: Error: Disk space is not enough...
I understand that when implementing configuration changes from vManage to cEdge/vEdge, the changes are made via NETCONF.However, even if no allow-service netconf is set under Interface tunnel, the configuration can be changed without any problem.Why ...
Hi Guys, Can somebody help to identify what might be the problem here? I'm trying to redistribute NAT DIA into BGP but it's not working. Please see screenshot below. It only worked as expected after I put network 0.0.0.0 statement on bgp.
While doing Cisco SDWAN cEdge routers configurations, we are unable to configure IPV4 address. We can only option of IPv6 address. Need help to configure IPV4 address. Thanks sdwaninterface GigabitEthernet0/0/0ip address 172.21.26.10 255.255.255.252 ...
Resolved! SD-WAN vEdge Upgrade path
Hello, team. Good day. We are planning to upgrade below platforms to 20.9.x. Is there any upgrade path ? - vEdge 5000 20.3.3 - vEdge 2000 20.6.3 - ISR1100-6G (Viptela OS) 20.6.3 Thanks.
hello, So in my lab i just have 3 CEDGE (CRSv) and i want to connect them to the controllers the only consideration is that the link are MPLS ONLY or in this case i put gi1 color private1 and gi2 color private2 on the SDWAN-DC device and i created r...
Hello , We would run dual stack (IPv4 & IPv6) at service side, and also we would run dual stack (IPv4 & IPv6) on the transport internet interface(underlay), on SD-WAN router. Is it possible to enable IPv4DIA (NAT44) and IPv6 DIA (NAT66) via the same...
